Victron Blue Smart IP65 charger 24/5(1) 230V | BPC240531064R

Victron battery charger 5A / 24V / 230V with IUoU charging characteristic

Blue Power, IP65 with DC connector, Bluetooth

Seven step smart charge algorithm, several other battery life enhancing features, Water, dust and chemical resistant

designed for Boats, Car, Caravan, Motor home ...

Ultra high efficiency “green” battery charger
With up to 95% efficiency, these chargers generate up to four times less heat when compared to the industry standard. And once the battery is fully charged, power consumption reduces to 0,5 Watt, some five to ten times better than the industry standard.

NEW! Bluetooth
The Blue Smart IP65 Charger is our new professional battery charger with Bluetooth built in! This enables you to see the information from your charger on your smartphone, tablet or computer, using the VictronConnect app.

Durable, safe and silent

• Low thermal stress on the electronic components
• Protection against ingress of dust, water and chemicals.
• Protection against overheating: the output current will reduce as temperature increases up to 60°C, but the charger will not fail.
• The chargers are totally silent: no cooling fan or any other moving parts.

Reverse polarity protected
Once the battery is connected, the charger immediately detects voltage and polarity. If the battery is connected incorrectly, all status-LEDs will start blinking. No sparks will occur.

Recovery function for fully discharged batteries
Most reverse polarity protected chargers will not recognize, and therefore not recharge a battery which has been discharged to zero or nearly zero Volts. The Blue Power Charger however will attempt to recharge a fully discharged battery with low current and resume normal charging once sufficient voltage has developed across the battery terminals.

Temperature compensated charging
The optimal charge voltage of a lead-acid battery varies inversely with temperature. The Blue Power IP65 Charger measures ambient temperature during the test phase and compensates for temperature during the charge process. The temperature is measured again when the charger is in low current mode during float or storage. Special settings for a cold or hot environment are therefore not needed.

Adaptive Battery Management
Lead-acid batteries should be charged in three stages, which are [1] bulk or constant-current charge, [2] absorption or topping charge and [3] float charge. Several hours of absorption charge are needed to fully charge the battery and prevent early failure to sulfation¹. The relatively high voltage during absorption does however accelerate aging due to grid corrosion on the positive plates.
Adaptive Battery Management limits corrosion by reducing absorption time when possible, that is: when charging a battery that is already (nearly) fully charged.

Storage mode: less corrosion of the positive plates
Even the lower float charge voltage that follows the absorption period will cause grid corrosion. It is therefore essential to reduce the charge voltage even further when the battery remains connected to the charger during more than 48 hours.

Reconditioning
A lead-acid battery that that has been insufficiently charged or has been left discharged during days or weeks will deteriorate due to sulfation. If caught in time, sulfation can sometimes be partially reversed by charging the battery with low current up to a higher voltage.
Remarks:
a) Reconditioning should be applied only occasionally to flat plate VRLA (gel and AGM) batteries because the resulting gassing will dry out the electrolyte.
b) Cylindrical cell VRLA batteries build more internal pressure before gassing and will therefore lose less water when subjected to reconditioning. Some manufacturers of cylindrical cell batteries therefore recommend the reconditioning setting in case of cyclic application.
c) Reconditioning can be applied to flooded batteries to “equalise” the cells and to prevent acid stratification.
d) Some battery charger manufactures recommend pulse charging to reverse sulfation. However, most battery experts agree that there is no conclusive proof that pulse charging works any better than constant voltage charging. This is confirmed by our own tests.

Lithium-ion (LiFePO₄) batteries
Li-ion batteries do not suffer from sulfation. But Li-ion batteries are very sensitive to under voltage or over voltage. Li-ion batteries therefore often have integrated cell balancing and under voltage protection (UVP) circuitry. Some reverse polarity protected chargers will not recognize a battery when the UVP has tripped. The Blue Power Charger will however automatically reset the UVP and start charging.
Important note: NEVER attempt to charge a Li-ion battery when its temperature is below 0°C.

Low current mode
Some lead acid batteries can overheat if charged with a current exceeding 0,3C (C is the capacity in Ah. A 12 Ah battery for example should not be charged with a current exceeding 0,3 x 12 = 4 A). The low current mode (charge current limited, see technical specifications) should therefore be used to charge low capacity lead-acid batteries.

Delivery contains:

• 5A IUoU Battery charger 24V, Blue Power IP65 Smart

For further Informations pleas use our FAQ: FAQ

Technical Details:

• Input voltage range: 180-265V AC
• Frequency: 45-65Hz
• Charge current: 5A
• Charge current in low current mode: 2A
• Minimum Battery capacity: 15Ah (Normal mode), 7Ah (low current mode)
• Efficiency: 95%
• Standby power consumption: 0,5W
• Minimum battery voltage: Starts charging from down to 0 V
• Back current drain: 0,7 Ah/month (1 mA)
• Charge outputs: 1
• Charge voltage 'absorption': Normal: 28,8V  /  High: 29,4V  /  Li-ion: 28,4V
• Charge voltage 'float': Normal: 27,6V  /  High: 27,6V  /  Li-ion: 27,0V
• Charge voltage 'storage': Normal: 26,4V  /  High: 26,4V  /  Li-ion: 27,0V
• Seven step smart charge algorithm
• Bluetooth: yes
• Can be used as power supply: yes
• Protection: Reverse polarity, Output short circuit, Over temperature
• Temperature compensation (lead-acid batteries only): 32mV / °C
• Operating temp. range: -30 to +50°C (full rated output up to 30°C)
• Humidity (non condensing): max. 95%
• Gehäusematerial: Kunststoff
• Battery-connection: Black and red cable of 1,5 meter, Connect clamps, M6 eyelet connectors
• 230 V AC-connection: Cable of 1,5 meter with CEE 7/7
• Protection category: IP65 (splash and dust proof)
• Weight: 0,9kg
• Dimensions (L x w x d): 190 x 95 x 47mm
• Standards (Safety): EN 60335-1, EN 60335-2-29
• Standards (Emission): EN 55014-1, EN 61000-6-3, EN 61000-3-2
• Standards (Immunity): EN 55014-2, EN 61000-6-1, EN 61000-6-2, EN 61000-3-3